Raptor and Talon Wireless Stomp Switches

Raptors and Bluetooth Talons are able to be controlled by the Stomp Switches. The basic information for using the stomp switches is listed below. Click on the links at the bottom of this page for additional information on using the Raptor, the Bluetooth Talon, using the handheld remotes, or wireless footswitches for the Raptor or Bluetooth Talons (optional accessory purchased separately).

Stomp_Switches.png

Pairing the Raptor and Talon Stomp Switches

Pairing a Wireless Stomp Switch to a Single Raptor

  1. Select a Wireless Stomp Switch to pair. Press and hold the Pairing Button on the Wireless Stomp Switch for at least 5 seconds. It must be the top right corner to initiate pairing. The three red LED's under the button will begin to scroll in a clockwise direction to indicate the switch is in Pairing Mode.
  2. Immediately press the Pair button on the Indicator Panel located on the Raptor Pump Assembly. The PAIR/Maintenance LED will begin to flash blue. The Raptor and Wireless Stomp Switch will go into Pairing Mode for 30 seconds. If a signal with three fast beeps from the Pump Assembly occurs, the Raptor and Wireless Stomp Switch have successfully paired. If 30 seconds pass while in Pairing Mode and they do not successfully pair, a chirp will sound from the Pump Assembly, signaling that the Pairing has timed out.
  3. If the Pair is unsuccessful, repeat the process.
  4. Repeat the complete pairing process for both Wireless Stomp Switches.

Pairing a Wireless Stomp Switch to Two Raptors

In order to Pair a Wireless Stomp Switch to the Raptor, please be sure to first Pair the Raptors together. When two Raptors are Paired together, any Wireless Stomp Switch that was Paired to an individual Raptor will no longer be Paired. Please see the "Pairing Two Raptors and Programming the Mounting Location" section of the Raptor Owner's Manual. If the two Raptors are already Paired together, a Wireless Stomp Switch can be Paired to either Raptor. When the Pairing process is complete, the Wireless Stomp Switch will be able to control both Raptors.

Pairing a Wireless Stomp Switch to a Single Talon

  1. Retract the anchor on the Talon by pressing the Up button on the Talon Indicator Panel.
  2. Once the Talon is fully retracted, select a Wireless Stomp Switch to pair. Press and hold the Pairing Button on the Wireless Stomp Switch for at least 5 seconds. It must be the top right corner to initiate pairing. The three red LED's under the button will begin to scroll in a clockwise direction to indicate the switch is in Pairing Mode.
  3. Immediately press and hold the Up button and the Down button simultaneously on the Indicator Panel on the Talon. The Depth Indication LEDs on the Indicator Panel of the Talon will begin to scroll. Once the LEDs are scrolling release the buttons on the Indicator Panel. The Talon and Wireless Stomp Switch will go into Pairing Mode for 30 seconds. If a signal with three fast beeps occurs, the Talon and Wireless Stomp Switch have successfully paired. If 30 seconds pass while in Pairing Mode and they do not successfully pair, an error tone will sound indicating that the pairing was not successful, and the Wireless Stomp Switch will not be able to control the Talon.
  4. If the Pair is unsuccessful, repeat the process.
  5. Repeat the complete pairing process for both Wireless Stomp Switches.

Pairing a Wireless Stomp Switch to Two Talons
In order to Pair a Wireless Stomp Switch to the Talon, please be sure to first Pair the Talons together. When two Bluetooth® Talons are Paired together, the Wireless Stomp Switch that was Paired to an individual Talon will operate both Talons. Please see the "Pairing Two Talons and Programming the Mounting Location" section of the Talon Owner's Manual. If the two Talons are already Paired together, a Wireless Stomp Switch can be Paired to either Talon. When the Pairing process is complete, the Wireless Stomp Switch will be able to control both Talons.

Clearing Paired Talons/Raptors from the Wireless Stomp Switches

  1. Select a Wireless Stomp Switch to clear. Press and hold the Pairing Button on the Wireless Stomp Switch for at least 5 seconds. It must be the top right corner to initiate pairing. The three red LED's under the button will begin to scroll in a clockwise direction to indicate the switch is in Pairing Mode.
  2. The Wireless Stomp Switch will go into Pairing Mode for 30 seconds. Once Pairing times out all Talon(s)/ Raptor(s) will be cleared.
  3. Repeat the complete clearing process for both Wireless Stomp Switches.

Battery

You will need 2 CR2450 batteries for the Raptor and Talon Stomp Switches (1 for each Stomp Switch).
CR2450.pngCR2450.png

How to Change the Battery

Stomp_Switches_Battery_Door.png

  1. With the back of the Wireless Stomp Switch facing you, use a large coin to rotate the Battery Cover counterclockwise until the Battery Cover loosens and cannot be turned any further counterclockwise.
  2. Remove the Battery Cover and the old battery. Replace the battery with a new CR2450 coin cell battery. Note the proper polarity of the battery.
  3. Ensure the rubber O-ring is properly seated in the underside of the Battery Cover.
  4. Replace the Battery Cover by aligning either of the Unlock icons with the Tabs, and pressing the cover down.
  5. Rotate the Battery Cover clockwise using the large coin until the Lock Icon aligns with the Tabs.

Using the Raptor Foot Switch

Stomp_Switches_with_Functions.png

  • Auto Up Button/ Pairing Button
    Single press to AUTO retract the anchor. For the Raptor anchor, press and hold to continually retract. The Raptor will continue to retract when the button is held until the button is released. The top right corner of this button is used to pair the Wireless Stomp Switch to a Talon or Raptor.
  • Auto Down Button/ Pairing Button
    Double press to AUTO deploy the anchor. For the Raptor anchor, single press and hold to continually deploy. The Raptor will continue to deploy when the button is held until it reaches its full range of operation or until the button is released. The top right corner of this button is used to pair the Wireless Stomp Switch to a Talon or Raptor.

Retracting the Raptor from the Wireless Stomp Switch

  1. To AUTO retract the Raptor, press and then release the Up button on the UP Stomp Switch. To CONTINUALLY retract the Raptor, press and hold the Up button.
  2. While AUTO retracting, the action can be paused by either pressing the Up button again, or by pressing the Down button. While the anchor is CONTINUALLY retracting, the action can be paused on the UP Stomp Switch by releasing the Up button.
  3. The paused retraction can be resumed by pressing the Up button again in the same manner.If AUTO retracting, the anchor will stop when the anchor is fully retracted. If CONTINUALLY retracting the button should be released when the anchor is fully retracted.

Deploy the Raptor from the Wireless Stomp Switch

  1. To AUTO deploy the Raptor, double press and then release the Down button on the DOWN Stomp Switch. To CONTINUALLY deploy the Raptor, press and hold the Down button.
  2. While AUTO deploying, the action can be paused by pressing the Down button again. While the anchor is CONTINUALLY deploying, the action can be paused on the DOWN Stomp Switch by releasing the Down Button.-The paused deployment can be resumed by pressing the Down button again in the same manner.
  3. If CONTINUALLY deploying the Raptor, and the anchor gets to its full length of travel, it will stop. If AUTO deploying the anchor, once the deploying anchor gets to its full length of travel or comes in contact with the bottom, it will go through an anchoring sequence determined by the current Mode and then stop.

Deploy the Talon from the Wireless Stomp Switch

  1. To deploy the Talon, double press the Down button on the DOWN Stomp Switch. While the anchor is deploying, the action can be paused on the DOWN Stomp Switch by pressing the Down button again.
  2. The paused deployment can be resumed by double pressing the Down button again.
  3. Once the deploying anchor gets to its full length of travel or comes in contact with the bottom, it will go through an anchoring sequence determined by the current Mode and then stop.

Retracting the Talon from the Wireless Stomp Switch

  1. To retract the Talon, press the Up button on the UP Stomp Switch.
  2. While the anchor is retracting, the action can be paused on the UP Stomp Switch by pressing the Up button.
  3. The paused retraction can be resumed by pressing the Up button again.
  4. Once the retracting anchor on the Talon gets to its full retraction it will stop. If the Talon is already fully retracted and the Up button is pressed again, an error tone will sound.

Range of the Remote

The range of the Raptor and Talon Wireless Stomp Switches is 30 feet. The range of the remote will be greatly reduced if it is used near or mounted to any metal object including aluminum or  steel. It is also recommended that the front end of the remote not be obstructed during use. 

Resources:

Was this article helpful?
0 out of 0 found this helpful

Articles in this section